el_baby

First of all, I've looked in most of the JDM Climate Control topics and I have find some people with the same problem, but they havent say how they solve it.

I have made the conversion, everything works fine except for the blower (and the A/C I dont know).

Some times the control unit blinks, and if I play with the temp the blinking stops.

Any idea of what could be causing it?


The problem with the blower is that with the unit not work. I have tested the voltages with the IG on, the #3 BLU/ORN (20 pin) have almost 12v and it shold be ground, the #9 WHT/BLU (16 pin) is ground and should have voltage, and the #1 BLU/RED (16 pin) have almost 12v and it should be ground or at least much less than 12v.

I was frustrated and decided to remove the pins, and for mistake I left the IG on, and removed the 20 pin, and with the 16 pin in the unit (the unit was off), the blower start to blow not at high speed but works. I tested the #9 WHT/BLU (16 pin) and it haved like 1.4v and the #1 BLU/RED (16 pin) have like 5.6v.

I connected the 20 pins, just from above (not full contact), and changes to high speed (the unit still off). Then I insert the pin full inside and the blower stopped.

I remove all the pins, and connect just the needed to the unit to power on and the needed for the blower, test it and nothing, test it again with the 16 pin (#9 WHT/BLU and #1 BLU/RED) alone, and the blower works at middle speed.

Then connecting some wires of the 20 pins, #3 BLU/ORN, #13 BLK/YEL, #16 BLK, Then I started to play with the #16 BLK and the blower start at full speed but the unit off, and removed the #16 and the turn to middle speed. I think that the same happens if I left the #16 in and take out the #13.

Any idea of what could be causing this problem? or what corrections should I make?


I have followed all the diagrams, pin outs, everything and just have that problem.
I havent connected the sensors yet.


The unit have a -1.5v | +1.5v switch in the bottom any idea for what it is?

el_baby

the problem was the control unit... I "burn it" mixing cables and buy other... the old one still working, but with the same problem of the blower... but the new one works fine

Blamo

I am having problems with my Air Mix Motor. Sometimes when I change the temp, the motor doesn't move at all until I hit the top number or bottom number (I.E. I am on 32, the air mix motor wont move until I hit 18). I am positive I wired it up via Jrcormier.com. Did you have this problem at one time? Maybe my air mix motor is bad?

__________________

94 Si

el_baby

I have almost the same problem with the old unit... my motor was changing in 24 to full "open" and it "close" when I get to 32... when I installed all the sensors it changes the temp of moving...
But with the new one it works fine

Your fan/blower works good?

Blamo

Yeah my fan blower works fine, and my recirculation works, and the mode works. Seems everything is working correctly except the air mix motor. Basically, I can only have it full open or full closed, so I'm guessing the Auto function will not work at this moment (I do not have A/C yet).

__________________

94 Si

el_baby

maybe the auto function will work... i think the most that it controls is the fan speed and the air mix motor...

so maybe in your case the auto function will regulate the fan speed than the air mix...

I dont have a/c yet neither, but i think that my auto works fine...


to make sure that the unit is fine sending the right signals to the air mix...
try connecting a voltimeter to the #4-red/yel and #12-red/wht of the 16pin
and then to the #7-gry and #8-pnk/blk of the 20pin
-i dont know if you need to disconnect the air mix to make that "test", try disconecting it, or both.

the air mix makes "big" moves like from 24 to 18, and "little" moves like from 25 to 32
-where it makes the "big" moves you should expect a change in voltage for more time...

so, if you see several changes in voltages, your unit should be fine
and then you wil need the air mix motor

el_baby

you have installed your air mix motor already?


here are 2 pics where I installed mine... so you dont have to remove the heater unless you have a "hose" or a tube that goes to the driver side of the heater (i think its not necesary)





lot of pages with climate control that i cant find where to put them..

new2imports

hey el_baby
sorry 4 budding in but my climite controls were all messed up, rear defrost didnt work A/C didnt work some of the vent settings also didnt work i did notice that when u shook the wiring harnesses that plugged into the back of the control modual they would flash on 4 a sec, as long as it was turned on, on the controller so i took the whole control modual right out from the car n opened it up n as im a electrical guy ive seen how these things r made n 2 fix this all u have 2 do is 2 resoldier the pins on the circuit board where the wiring harness plugs into. U might as well do all the soldier points on the board just so u know that after u do that u'll never have another problem with it ever again, do the same thing 2 ur main relay as well same problem with those things as well
And its not a hose but a cable lol

Knicelude123

hey guys i have no ac at all like my slider for heat and cool air doesnt go to the cool side any idea how to fix ?

new2imports

hey Knicelude123
try disconnecting the cable that operates the vent at the heater box under the passenger side dashboard n then try 2 slide it again if it still doesnt work when its disconnected then check it on the climate control modual side could also b a sezied inside the control modual or a sezied vent.